Last edited by Dolrajas
Friday, July 31, 2020 | History

2 edition of Specification for flanges and bolting for pipes, valves and fittings found in the catalog.

Specification for flanges and bolting for pipes, valves and fittings

British Standards Institution.

Specification for flanges and bolting for pipes, valves and fittings

by British Standards Institution.

  • 383 Want to read
  • 27 Currently reading

Published by B.S.I. in London .
Written in English


Edition Notes

With amendments as issued.

StatementBritish Standards Institution.
SeriesBS 10
The Physical Object
Pagination55p.
Number of Pages55
ID Numbers
Open LibraryOL14371460M

ASME B is a standard for Pipe Flanges and Flanged Fittings that covers flanges sizes from NPS ½” to 24” Whereas ASME B is a standard for Large Diameter Steel Flanges that covers flanges sizes from NPS 26” to 60” ASME B is the standard for Cast iron pipes flanges & flanged fittings. EN Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories. BS Standards BS Specification for Flanges and Bolting for Pipes, Valves and Fittings. This covers plain, boss, integrally cast or forged, and welding neck type flanges, in ten tables.

Flanges and their joints Circular flanges for pipes, valves, fittings and accessories, Class designated Part 1: Steel flanges, NPS 1/2 to 24 The European Standard EN has the status of a British Standard ICS 2 DUCTILE-IRON PIPE AND FITTINGS had been achieved in producing lower-cost iron by using coke instead of charcoal. Fol-lowing this success, the more progressive cities began to install cast-iron mains. The use of cast-iron pipe was introduced in the United States in the early Size: 1MB.

Standards & Specification Shin Nan ductile iron pipes and fittings for water and sewerage systems are manufactured according to EN / EN / EN / ISO and under the quality control system of ISO for quality assurance. The standard nominal sizes DN of pipes to fittings are from 80 mm to mm. Weldbend is the ONLY domestic manufacturer of both carbon steel fittings and flanges. Weldbend is proud to be America's choice for domestically manufactured carbon steel butt-weld fittings & flanges ½" – 60" News. Visit the news page for up-to-date information about Weldbend.


Share this book
You might also like
National program coordination

National program coordination

Visual Basic design patterns

Visual Basic design patterns

Warfare; A Study Of Military Methods From The Earliest Times

Warfare; A Study Of Military Methods From The Earliest Times

Equine Exercise Physiology 2

Equine Exercise Physiology 2

By sea to the Isles.

By sea to the Isles.

tops of porphyry copper deposits - mineralization and plutonism in the Western Cascades, Oregon

tops of porphyry copper deposits - mineralization and plutonism in the Western Cascades, Oregon

Soviet human rights policy and perestroika

Soviet human rights policy and perestroika

Claudian

Claudian

A companion to Charles Dickens

A companion to Charles Dickens

prediction of school adjustment.

prediction of school adjustment.

Developmental response to increased blood flow in the rabbit carotid artery

Developmental response to increased blood flow in the rabbit carotid artery

Spring 2004 departmental report

Spring 2004 departmental report

economic survey method for small areas

economic survey method for small areas

Death of a warrior queen.

Death of a warrior queen.

Pennine Way

Pennine Way

Understanding California real estate law

Understanding California real estate law

Specification for flanges and bolting for pipes, valves and fittings by British Standards Institution. Download PDF EPUB FB2

14ANVIL® PIPE FITTERS HANDBOOK. NOTE:The Gruvlok Fig. Flange requires the use of a Flange Adapter Insert when used against rubber surfaces (Figure C1), serrated flange surfaces or mating flanges with inserts (Figure C2).

The Flange Adapter Insert File Size: 2MB. Purchase your copy of BS as a PDF download or hard copy directly from the official BSI Shop. All BSI British Standards available online in electronic and print formats. BS - Specification for flanges and bolting for pipes, valves and fittings.

Publisher Summary. This chapter summarizes ANSI buttweld fittings, which are used to change direction or join parts of a piping system. valves and fittings book Different types of buttweld fittings include elbows, reducing elbows, degree elbows, degree returns, tees, crosses, eccentric and concentric reducers, lap.

Related Topics. Dimensions - Sizes valves and fittings book dimensions of pipes and tubes, and their fittings - inside and outside diameter, weight and more ; Related Documents. ANSI - American National Standards Institute - ANSI provides a forum for development of American national standards; ANSI B - Steel Pipe Flanges - Pressure and Temperature Ratings - Group - Pressure (psig) and temperature ratings.

ASTM A This specification covers forged or rolled alloy and stainless steel pipe flanges, forged fittings, and Valves and parts for high-temperature service.

ASTM A Specification for several grades of carbon and low alloy steel forged or ring-rolled flanges, forged fittings and Valves for low-temperature service. Piping class or Pipe Class is a document that specifies the type of the components such as a type of pipe, schedule, material, flange ratings, branch types, valve types and valve trim material, gasket and all the other components specific requirements to be used for different fluids under different operating conditions in a plant.

Flange joints require proper tightening to avoid the leak of the fluid from the joint. Bolt tightening sequence or torque sequence is key to achieve this. Torque table provides the required value for bolt tightening.

A complete torque tightening procedure. (PROJECT STANDARDS AND SPECIFICATIONS) TABLE OF CONTENTS 1 GENERAL 2 General 9 Chemical Composition 12 3 PIPING COMPONENTS 12 Pipes 12 Fittings 15 Flanges 19 Gaskets 23 Bolts and Nuts 25 Branches 27 KLM Technology Group has developed; 1) Kolmetz Handbook of Process MSS-SP Standard Marking System for.

Flange Specifications The standard flange drilling is normally PN16, on pipes and fittings for working pressures up to and including 16 Bar.

Other drilling configurations (PN10, PN25, PN40) require the corresponding number and size of bolts in a set for the specified drilling arrangement. Bolt sets (Extra Long) for PN16 flanges - DI x PE Joint. It is basically flange part but covered under ASME B that is why it is considered as pipe fittings.

Piping Union Unions are used as an alternative to flanges connection in low-pressure small bore piping where dismantling of the pipe is required more often. buy bs (): specification for flanges and bolting for pipes valves and fittings metric series - copper alloy and composite flanges from sai global.

buy bs 10(): specification for flanges and bolting for pipes, valves and fittings from sai global. THREADED FLANGE Threaded flanges are joined to pipes by screwing the pipe (which has a male thread, generally NPT per ASME B) onto the flange, without seam welds (in certain cases, though, small welds are applied to increase the strength of the connection).

Threaded flanges are available in sizes up to 4 inches and multiple pressure ratings, however, they are used, mostly, small size.

Specifies requirements and dimensions for circular, plate blank, boss, integrally cast or forged and welding-neck type flanges or nominal sizes DN 15 to DN and their bolting for use on pipes, valves and fittings and other pressure-retaining equipment containing fluid at pressures up to kPa and at temperatures in the range °C to +°C.

AN AMERICAN NATIONAL STANDARD ASME B (Revision of ASME B) Pipe Flanges and Flanged Fittings NPS 1/2 Through NPS 24 Metric/Inch Standard. Stud bolt, nuts, machine bolts and washers are also known as bolting material or fastener. Bolting is the term that used to tighten / create the flange joints connection.

Tightening of the flange ensures the leak-proof connection between gasket & flanges. ASME flanges have a minimum four bolt hole and for higher diameter flanges, the number of bolt holes is always in multiples of four.

This Standard specifies requirements for circular flanges of nominal sizes DN 15 to DNinclusive, and their bolting for use on pipes, valves, fittings and other pressure-retaining equipment containing fluid at pressures up to 19 kPa and at temperatures in the range C to + flanges are manufactured from carbon steel, carbon-manganese steel, alloy steel, stainless steel.

ANSI Standards. B Unified Screw Threads. B Cast Iron Pipe Flanges and Flanged Fittings (25, and lb) B Bronze Flanges and Flanged Fittings ( and lb) B Steel Pipe Flanges and Flanged Fittings (,and lb Including Reference to Valves) B Square and Hex Bolts and Screws.

Flanges are commonly used to connect valves into pipework making it easier for removal and maintenance. There are many common flange standards and flanges within the same standard can etiher be flat (commonly cast iron, ductile iron) or raised face (commonly cast steel and stainless steel).

Below is a reference table for critical flange dimensions to help identify what standard you have. The ASME - American Society of Mechanical Engineers - ASME/ANSI B16 Standards covers pipes and fittings in cast iron, cast bronze, wrought copper and steel.

ASME/ANSI B - - Cast Iron Pipe Flanges and Flanged Fittings. This Standard for ClasCast Iron Pipe Flanges and Flanged Fittings covers. Section 2: Laminates Manufacturing Methods Ershigs, Inc. offers two standard types of FRP laminate construction for piping and duct systems: Filament Wound, and Contact Molded (hand lay-up).

Filament Wound Construction- This process utilizes continuous glass strand roving that is pre-saturated in a resin.Installation Instructions Flange Bolt Torque Guidelines. These guidelines are intended for bolting of PVC flange adapters.

Tighten bolts by hand until they are snug. Establish a uniform pressure over the flange face by tightening the bolds in 5ft/lbs increments to the torque valves listed in the table below using a degree opposing.Describes carbon steel, alloy steel, cast iron and copper alloy flanges, and appropriate bolts and nuts, for use with pipes, valves and fittings containing steam, oil, compressed air or water within temperature range Degrees C to Degrees C and pressure up to lbf/sq ins.